The Denso 095000-6410 fuel injector, while a seemingly simple component, incorporates several key technical advantages that contribute to engine performance, efficiency, and reliability. These advantages are a result of Denso’s expertise in precision manufacturing and materials science.Here are the primary technical advantages of this specific injector:

1. Exceptional Precision and Flow Matching

Tight Manufacturing Tolerances:Denso manufactures these injectors to extremely precise specifications. This ensures minimal variation in flow rates from one injector to another.

Inherently Matched Sets:Because of this precision, a set of new 095000-6410 injectors is essentially “flow-matched” from the factory. This is critical for engine balance; all cylinders receive the same amount of fuel for a given injector pulse width from the ECU, leading to smooth operation, optimal power, and minimal emissions.

2. Superior Atomization

Disc-Type Multi-Hole Design:Unlike older pintle-style or single-hole injectors, the 095000-6410 typically uses amulti-hole discat its tip.

Advantage:This design breaks the fuel into a finer, more consistent spray pattern (a mist rather than a stream). Better atomization allows the fuel to vaporize more completely and mix evenly with the air in the intake manifold. This results in:

More efficient combustion.

Increased power output.

Reduced unburned hydrocarbon (HC) and carbon monoxide (CO) emissions.

3. High-Impedance Design

Simplified Electrical Control:As a high-impedance (typically 12-16 ohms) saturated solenoid injector, it has significant advantages for the vehicle’s electronic control unit (ECU):

Lower Current Draw:It operates on less current than low-impedance injectors, reducing the electrical load on the ECU drivers.

No Need for Resistor Packs:Unlike low-impedance injectors, it does not require an external resistor pack to limit current, simplifying the wiring harness and overall system design.

Precise Control:The saturated circuit allows the ECU to open and close the injector with very precise timing, which is crucial for modern fuel strategies.

4. Rapid Response Time

Fast Opening and Closing:The injector’s solenoid and internal spring are engineered for very quick reaction times. It opens and closes rapidly in response to the ECU’s signal.

Advantage:This fast response allows for extremely precise fuel metering, especially at low pulse widths (idle, low load). This precision is essential for modern engines to meet strict fuel economy and emissions standards without sacrificing drivability.

5. Robust and Durable Materials

Longevity and Chemical Resistance:The injector is constructed from materials designed to withstand a harsh environment:

Heat Resistance:It can endure the high temperatures of the engine bay and intake manifold.

Fuel Compatibility:The internal components and seals are resistant to modern gasoline formulations, including those with ethanol (E10, E15).

Durable Coil:The solenoid coil is well-insulated and protected, ensuring reliable operation over a long service life.

Here is a detailed breakdown of what it is, what vehicles it fits, and important information about it.

1. What is this Injector?

TheDenso 095000-6410is asaturated-type, high-impedancefuel injector. This is a standard solenoid-operated injector used inPort Fuel Injection (PFI or MPI)systems, where it is mounted in the intake manifold, spraying fuel just upstream of the intake valve.

Saturated-Type:This refers to the electrical driver circuit used by the vehicle’s ECU. It’s a simpler, slower-acting circuit compared to “peak and hold” injectors (which are low-impedance). This is the most common type for many modern vehicles.

High-Impedance:It has a high electrical resistance (typically 12-16 Ohms). This means it draws less current and can be driven directly by the ECU without needing a separate resistor pack, which low-impedance injectors often require.

2. Key Specifications

Flow Rate:Approximately~310 cc/min@ 3 Bar (43.5 PSI). (Always confirm the exact flow rate for your specific application, as it can vary slightly).

Connector Type:USCAR (a common modern standard) or a similar oval-shaped electrical connector.

Seal Type:It uses both upper and lower O-rings for sealing, and often a small plastic insulator or spacer at the top.

3. Common Vehicle Applications

This is a very popular injector and is used as original equipment (OE) on many Toyota, Lexus, and Scion models from the mid-2000s to the early 2010s.Always cross-reference your VIN number with a reliable parts catalog before purchasing,but common fits include:Toyota:

Toyota Camry (especially 2007-2011 with the 2AZ-FE 2.4L engine)

Toyota RAV4 (2006-2012 with the 2AZ-FE 2.4L engine)

Toyota Highlander

Toyota Avalon

Toyota Sienna

Toyota Venza

Lexus:

Lexus ES 350